Shure MX185
Lavalier Microphone
Shure Microflex® MX100 Series microphones are wired lavalier electret condenser microphones designed for speech and vocal pickup, general purpose sound reinforcement, recording, and remote monitoring applications. They can be clipped to neckties, lapels, and other articles of clothing. Interchangeable cartridges make it possible to easily reconfigure microphone coverage as the need arises.
- Wide dynamic range and frequency response for accurate sound reproduction
- Interchangeable cartridges that provide a choice of polar pattern for each application
- Rotatable tie-clip that pivots in 90° increments for placement flexibility
- Dual tie-clip and belt-clip preamp
- Supplied with snap-fit foam windscreen that controls breath noise
- Balanced, transformerless output for increased immunity to noise over long cable runs
- RF filtering
Interchangeable Cartridges
Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.
Windscreen
Foam Screen
Slip the windscreen over the top of microphone so it covers side slots. The foam windscreen provides 5 to 10 dB of "pop" protection.
Snap-Fit Windscreen
- Snap into the groove below the cartridge.
- To remove, spread the gap with a screwdriver or thumbnail.
- Provides 30 dB of "pop" protection.
Preamp Gain
If necessary, the preamplifier gain can be reduced by 12 dB. Contact an authorized Shure service center for information.
RFI Filtering
Important: Microphones must be used with the RK100PK or RK202PK plate-mounted preamp to optimize RF immunity.
General Rules for Lavalier Microphone Use
- Attach the microphone approximately 76 mm to 152 mm (3 to 6 in.) below the neckline for the best sound.
- Do not cover the microphone with your hand or clothing.
- Use one of the supplied windscreens to minimize wind and breath noise.
- If four or more microphones will be active at any given time, use of an automatic mixer, such as the Shure SCM810 or SCM410, is recommended.
Tie Clip
Insert the top of the microphone through tie clip loop from below until tie clip loop snaps into place over the lower groove on the microphone.
Specifications
Type
Electret Condenser
Frequency Response
50–17000 Hz
Polar Pattern
MX185: Cardioid
Output Impedance
180 Ω
Output Configuration
Active Balanced
Sensitivity
@ 1 kHz, open circuit voltage
Cardioid: -35 dBV/Pa (18 mV)
1 Pa=94 dB SPL
Maximum SPL
1 kHz at 1% THD, 1 kΩ load
Cardioid: 124 dB
Self Noise
A-weighted
Cardioid: 28 dB SPL
Signal-to-Noise Ratio
Ref. 94 dB SPL at 1 kHz
Cardioid: 66 dB
Dynamic Range
1 kΩ load, @ 1 kHz: 96 dB
Common Mode Rejection
10 Hz to 100 kHz: 45 dB, minimum
Clipping Level
at 1% THD: –6 dBV (0.5 V)
Polarity
Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector
Environmental Conditions
Operating Temperature | –18–57°C (0–135°F) |
Storage Temperature | –29–74°C (–20–165°F) |
Relative Humidity | 0–95% |
Power Requirements
11–52 V DC, 2.0 mA
Cable
1.2 m (4 ft)
Certifications
Meets essential requirements of all applicable European Directives.
Eligible for CE marking.
Note: Testing is based on the use of supplied and recommended cable types. The use of other than shielded (screened) cable types may degrade EMC performance.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: info@shure.de
Titel | Type | Størrelse | Download |
---|---|---|---|
MX183_4_5_Spec_Sheet.pdf | 120.60KB | Download |